Driver Backup In Fedora 10
location: linuxquestions.com - date: May 9, 2009
I would like to know how to take back up of non fedora10 drivers and restore them after formatting the PC.
The same i have done in Windows XP using driver magician software.
But how to do it in fedora?
A same problem had been posted earlier but i could find any solution for non fedora drivers i.e those that are not compiled with the kernel.
And also how would one restore it if the PC is formatted?
Thanks in advance.
Intel GMA 500 Driver Installation problem in Fedora 10
location: linuxquestions.com - date: December 1, 2009
My laptop's graphics display is Intel Graphics Media Accelerator 500 and my display can support 1366 x 768 resolution. Laptop Model No. is Sony vaio CX113KG. When I try to install Fedora 10 it starts in text mode. When I give the command startx it gives the following error.
(EE)Unable to locate /open config. gile
New driver is "Intel"
Fatal Server Error
no screens found
Kindly help me how to fix this issue.
How to install Ns2.26 on ubuntu 10.04 or fedora 10
location: linuxquestions.com - date: April 23, 2013
I want to ask question about ns2.26 . so i started new thread.
I want to install nrlsensornet with ns2.26 on either fedora 10 or ubuntu 10.04
Is this possible?
I came to know that ns2.26 is can not be installed on fedora 10. how to degrade my system to fedora 8.
how to enable or install SATA AHCI driver in Ubuntu 10.04
location: ubuntuforums.com - date: January 4, 2012
I need to find out how to enable or install the SATA AHCI driver in Ubuntu 10.04 when I have the BIOS serial ATA setting to the IDE compatibility mode ? This is a multi-boot system from 2009 with a few versions of Windows installed, (all were installed when in the IDE emulation compatibility mode, and now changing it to AHCI mode in the BIOS). It has a ASUS P5QL motherboard with the Intel P43 express IHC10 chip set.
[SOLVED] how to enable or install the SATA AHCI driver in Ubuntu 10.04
location: linuxquestions.com - date: January 4, 2012
I need to find out how to enable or install the SATA AHCI driver in Ubuntu 10.04 when I have the BIOS serial ATA setting to the IDE compatibility mode ? This is a multi-boot system from 2009 with a few versions of Windows installed, (all were installed when in the IDE emulation compatibility mode, and now changing it to AHCI mode in the BIOS). It has a ASUS P5QL motherboard with the Intel P43 express IHC10 chip set. My Ubuntu 10.04 has all the updates and works fine.
clone ubuntu 8.04 okay, but not CentOS 5.2 and Fedora 10.
location: linuxquestions.com - date: June 27, 2009
I have successful tar an existing CentOS 5.2 partition from Fefora10.
The idea is to move a working CentOS 5.2 residing in an internal hard drive to a portable hard drive.
I know how to edit a stencil in menu.lst to boot the clone CentOS5.2.
During boot, I encountered
Ubuntu 8.10 Tata Photon USB Mode Driver like Ubuntu 10.04
location: linuxquestions.com - date: July 24, 2010
I have been using Ubuntu since 7.04. It is really an amazing experience. I have some 8.10 machines which I use for my students and i don't want to change it right now to different version. On the other hands I want to install USB Modem (Tata Photon+) on Ubuntu 8.10. I have seen its working fine on Ubuntu 9.04 and even better with Ubuntu 10.04.
Can any one help me for how to install drivers in Ubuntu 8.10 for proper support with Tata Photon. right now my usb modem is detected as usb storage. I have also tried the usb-switchmode stuff following some articles available on net. But with no real success.
I want to know the exact difference in 8.10, 9.04 and 10.04 as far as usb modem driver installation is concerned.
Or can I configure Ubuntu 8.10 in such a way that I can use USB Modem (Tata Photon) like we do in Ubuntu 10.04.
Your help will be heartily appreciated
Thanks & Regards
Fedora 10: Is Intel GME965 using the wrong DRM module (i915)?
location: linuxquestions.com - date: January 14, 2009
lspci, xorg.conf, etc. at the end of this post
I'm following the directions at
because I suspect OpenGL is being rendered in software instead of hardware.
$ dmesg | grep agp
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 965GME/GLE Chipset
agpgart-intel 0000:00:00.0: detected 7676K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
$ dmesg | grep drm
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized i915 1.6.0 20080730 on minor 0
As you can see, i915 is selected...? It also shows up here:
Module Size Used by
i915 53508 2
drm 158260 3 i915
The site says: "If you get DRM version output but not your card-specific DRM version output, you may not have a supported card, or it may not be getting probed due to the PCI ID being missing from the driver.
How to install Ns2.26 on ubuntu 10.04 or fedora 10 Page 3
location: linuxquestions.com - date: April 28, 2013
# 30 .
No answers until you have replied to post # 28.
And you will have to check ns-allinone-2.26/ns-2.26/Makefile :
Line 37 : CC = gcc32
Line 38 : CPP = g++32
If any different from gcc32 / g++32 : Start from scratch.
Driver backup utility in ubuntu ??
location: linuxquestions.com - date: January 17, 2012
the following are the driver backup utilities which I have found on the net
i) Double Driver
ii) Chilly device driver backup
iii) Jermar softwares WinDrivers backup
iv) Fabs Auto backup
unfortunately all these are meant for windows O.S , now my question is there a similar utility for linux?
Page: 1 2 3 4 5 6 7 8 9 10